tplink-banner

AC2600 MU-MIMO WiFi Router Archer C2700

This router from the is one of the best wireless routers form the TP-Link. It truly designs to provide constant speed to wired and wireless devices. The powerful antennas are pre-optimized to provide uninterrupted wireless signals to all the wireless connected devices such as mobile or gaming devices. In addition, you can easily set up the Archer C2700 router by using the TP-Link web interface “www.tplinkwifi.net”. Whereas, It comes with four ethernet ports to provide better speed on wired devices, which are located at the backside of the router.

How to connect Archer C2700 WiFi router on ISP modem?

The following guide provides you instructions on how to connect your Archer C2700 router “www.tplinkwifi.net”.

You can connect the router via different methods such as wired connection, wireless connection or by using a WPS button.

Before starting the process, make sure you have an active internet modem from the internet service provider.

After connecting hardware on your router, the next important thing is to position the router.

Because of positing of the router is a very important thing to get the best performance from your TP-Link router. 

NOTE– We suggest you place your Archer C2700 router from away from the excessive heating area and the WiFi router should not be located near electromagnet devices such as Microwave, Printer, Smart TV.

Keep it away from moisture area. Make sure the cables between the router and the devices should not be overlapping. 

C2700 WiFi router on ISP modem

After putting your Archer C2700 WiFi router, follow the below steps to connect your router. 

To connect your Archer C2700 WiFi router to the ISP modem. 

  • Turn off the ISP modem and if the modem has backup batteries, remove them.
  • Connect Ethernet Cable– Get an ethernet cable and plug it into the modem and connect the other end into the yellow-colored internet port of your Archer C2700 WiFi router.
  • After connecting the ethernet cables thereafter turn on the modem and wait for a few minutes.
  • Connect the power adaptor of your Archer C2700 to your nearby power source and turn it on.

After connecting the router to the modem, you need to connect your router to the computer through wired or wireless. 

Method 1 Connection by a wired device

Method 1 Connection by a wired device.

  • Connect an ethernet cable– Get an ethernet cable and plug one end of it into the internet port on the back panel of your and connect the other into the ethernet port of your computer.
    NOTE– Make sure you turn off the WiFi of your computer while connecting the router through an ethernet cable.
  • Once ethernet cable connects correctly, open any browser on your computer to get the setup page for Archer C2700 WiFi router. As a result, follow the display instructions to set up the router.

Method 2- Connection by a wireless device

  • Open Wireless settings on your computer or your wireless device and search for TP-Link (SSID) Network name. NOTE– The default username for TP-Link routers are like TP-LINK_XXXX or TP-LINK_XXXX_5G.
  • Click on the network name (SSID) and enter the network security key (WiFi password). 

NOTE– You can find the Network name (SSID) and network security key (WiFi password) on the product label at the bottom side of the router.
Therefore, click on the connect button to connect your wireless device on the Archer C2700 WiFi router.

Method 3 – Connection by WPS Push-button. 

Any device which supports WPS such a mobile device, tablet, printers, etc connect to the router through this method.

This method is the easiest way to connect your wireless devices on your Archer C2700 WiFi router.

NOTE– WPS is not available on IOS devices.

  • On your android device, go to the WiFi settings and tap the WPS icon.

    NOTE– If you cannot find the WPS option on your device screen, go to the WiFi settings and click on more to get the WPS option.

Connection by WPS Push-button
  • Now go the router and locate the WPS push button at the back or side panel of your router. Press it within two minutes.
  • It connects your device. If you face any issue while connecting the router, then please contact the support team.

How to login into the Archer C2700 WiFi router?

It is easily to log in to the Archer C2700 WiFi router with the help of the web interface of the router. You can manage your router from the web-based management page “www.tplinkwifi.net” of Archer C2700 WiFi router. 

Herer, you can use the TP-Link web-based utility on any Windows, MAC or UNIX operating system.

You can use all the leading browsers to login into the Archer C2700 WiFi router such as Microsoft Internet Explorer, Apple Safari, Mozilla Firefox or Google Chrome.

Follow the below instructions to login into the Archer C2700 WiFi router. 

Steps To login into the Archer C2700 WiFi router. 

  • Open a web browser on your computer and type http://tplinkwifi.net into the web address bar and press enter. 
  • You can also enter the IP address of your router to get the login screen of your Archer C2700 WiFi router.
  • A login screen displays to create the Administrator password for your router. 

If the login screen doesn’t appear on your device screen. In last, please contact the support team. 

NOTE– You can use the admin password to login into the router. This is not a WiFi password or network security key your TP-link router.

It is advisable to create a strong password by using the combination of alphabets and numerical. 

After creating the password, click on Let’s get started button.

Your task is complete.

For more information about this topic or any other related topic. At this point, please contact the support team.

How to register TP-Link ID

How to register TP-Link ID?

This article provides you instructions on how to register your TP-Link ID. You can register the TP-Link ID at the time of the initial setup process but if you haven’t registered TP-Link ID.

You can follow the below instructions. 

Steps to register a TP-Link ID.

  • Launch a web browser on your computer and type “http://tplinkwifi.net” into the web address bar and press enter. You can also enter the IP address “192.168.1.1” of your router to get the login screen of your Archer C2700 WiFi router.
  • Login prompt displays on your device screen to enter the admin password for your router which you set at the time of the initial setup.

If the login screen doesn’t appear on your device screen, please contact the support team.

  • A web-based utility homepage displays.
  • Now go to Basic and click on TP-LINK Cloud.
  • Click Register Now at the bottom of the page and after that follow the instructions to complete the registration process.
  • Once you register your TP-Link ID, go back to the TP-LINK Cloud page.
  • On the login screen, enter the username and password in the required fields and click on the login button.

How to Manage the Router via TP-Link Tether App?

TP-Link makes very easy to manage your router from the TP-Link Tether App by installing it on any android and IOS devices such as smartphones, tablets or I-Pad.

This app supports both the android and IOS operating devices.

From the TP-Link Tether App, you can perform the major actions on your router such as rebooting, Firmware update, check device connection status and changing the wireless settings.

NOTE– Before starting the process, You must have registered your TP-Link ID by “www.tplinkwifi.net” before and have all the information about router such as the admin password of your router. 

How to Manage the Router via TP-Link Tether App

Steps to Manage the Router via TP-Link Tether App. 

  • You need to connect your device on a TP-Link wireless network.
  • Open the Apple App Store or Google play store and search for “TP-Link Tether” app. Download and install it on your device.

    NOTE– You can also scan the QR scan code to install the “TP-Link Tether”. You can find it in the product manual.

  • Open the “TP-Link Tether” app and select the model of your router.

  • Now you need to log in with the TP-Link ID or with the admin password for the router. 

The process is complete and now you manage your router as needed. If you are facing trouble during the above process, please contact the support team for more information on this topic. 

How to Set Up Remote Management on TP-Link WiFi routers?

In this guide, you will get to know the basic steps to Set Up Remote Management on TP-Link WiFi routers. You can perform this task easily by using the web utility of the TP-Link router. These basic steps apply to most of the TP-Link WiFi routers and may some models have different page appearance depending on the router model number. 

You can perform these steps

Steps to  Set Up Remote Management on TP-Link WiFi routers

  • You need to connect your device on a TP-Link wireless network.
  • Open a new web browser on your computer and type “http://tplinkwifi.net” into the web address bar and press enter.
  • You can also enter the default IP address “192.168.1.1” of your router to get the login screen of your router.
    NOTE– To know the default IP address of your router, contact the support team.
  • A login page displays to enter the login credentials.
  • Enter the admin password and click on Login.

If the login screen doesn’t appear on your device screen, please contact the support team. 

  • A router web-based homepage displays on your device screen.
  • Go to Advanced and then click on System Tools.
  • Under the Administration, go to the Remote Management settings.
  • On Remote Management page, Select Enable Remote Management for all devices.
  • You can select the Web Management Port field, type 80 or 1024-65535.
  • In the Remote Management IP address field, enter the IP address of the remote device to manage the router.
  • Click on the Save button to save the new settings.

Now you can manage the router from a remote device. You can control all the settings of your router from the remote device. 

If you find any difficulties while performing the above steps. Please contact our support team. 

What should I do if I forget my TP-Link router WiFi password?

If you forget the WiFi password of your TP-Link router, you can recover it by login into the web interface of your TP-Link router. If you haven’t change the default WiFi password, you can find it on the product label at the bottom of the router. You can follow the below steps to recover the wireless password of your TP-Link router. 

Steps to recover the wireless password of your TP-Link router. 

  • Connect your device to the router through an ethernet cable.
    NOTE– You can also perform this action on wirelessly connected devices, but we suggest you do it on a wired connection to avoid any trouble.
  • Open a new web browser on your computer and type http://tplinkwifi.net into the web address bar and press enter.
  • A login page displays. You can log in with the TP-Link ID or with the admin password of your router. 

If the login screen doesn’t appear on your device screen, please contact the support team. 

  • Go to Basic and click on Wireless.
  • Under Wireless, see the wireless information about your router such as Network name (SSID) and Network wireless (WiFi) password.
  • On some router models, WiFi password shows as Network Security key.
  • From this Wireless settings page, you can change the Network name (SSID) and Network wireless (WiFi) password of your router. 

Now you can connect your device on your TP-Link router network.

If you are still struggling to recover the Network wireless (WiFi) password of your router, please contact the support team.

You can also contact support the team for more information about each feature of the TP-Link router.